Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.
✓ Derinimas failu (flash)
✓ Galimas papildomas modulis 10 programinės įrangos versijos
Transporto priemonės duomenys
| Markė | BMW |
| Modelis | 5 SERIES G30/G31/G38 |
| Variklis | 518d 2.0L L4 16V 110kW/148HP DME__DDE803P |
| Serijinė galia | 150 CV / 11 kW |
| Darbinis tūris | 2000 cc |
| Kuras | Diesel sovralimentato |
| Transporto priemonės tipas | Auto |
ECU
| Gamintojas | BOSCH |
| Modelis | MD1CS001 (DME__DDE803P) |
| Atmintis / EPROM | Micro Infineon TRICORE categoria AURIX. Il micro ha una DFLASH da 848 Kbyte |
Galimos derinimo operacijos / parinktys:
- Boost pressure limiter
- Boost pressure limiter 2
- Boost pressure
- Boost pressure 10
- Boost pressure 11
- Boost pressure 12
- Boost pressure 14
- Boost pressure 3
- Boost pressure 4
- Boost pressure 5
- Boost pressure 6
- Boost pressure 7
- Boost pressure 8
- Boost pressure 9
- Max accepted exhaust gas temperature value after turbine
- Max accepted exhaust gas temperature value at particulate sensor
- Exhaust gas temperature
- Protection for engine overheating
- Protection for engine overheating 2
- Protection for engine overheating 3
- Max CAT temperature threshold for component protection
- Basic torque management at engine cranking
- Injection period
- Injection period 3
- Injection period 4
- Injection period 5
- Injection period 6
- Maximum injection period
- Injection opening time related to inj. pressure
- Initialization values over pressure control valve
- J
- Torque limiter 2
- L
- Torque limiter 4
- Boost pressure deviation limits for basic charge air pressure
- Boost pressure deviation limits for basic charge air pressure 2
- Torque limiter
- Torque limiter for diagnostic
- Torque limiter during particulate filter overloading - pressure
- Torque limiter during particulate filter overloading - pressure 2
- Torque limiter during particulate filter overloading - temperature
- Lambda value of the smoke limitation
- Lambda value of the smoke limitation 2
- Maximum engine torque at crank shaft
- Maximum engine power
- Protection for fuel overheating
- Specific injection pressure limiter
- Specific injection pressure limiter 2
- Specific injection pressure limiter for EFT sensor
- Max rail pressure setpoint increase per s
- Specific injection pressure
- Specific injection pressure 2
- Specific injection pressure 3
- Specific injection pressure 4
- CAT upstream temperature sensor characterization
- DPF upstream temperature sensor characterization
- EGT sensor thresholds on CAT for diagnosis
- EGT sensor thresholds on DPF for diagnosis
- Torque limiter in recovery mode
- Variable geometry duty cycle limit
- Variable geometry duty cycle limit 2
- Variable geometry duty cycle limit 3
- Variable geometry duty cycle limit 4
Programinės įrangos identifikatoriai (10)
| Aparatinės įrangos Nr. | Programinės įrangos Nr. (lustas) | Versija | Atnaujinimo programinė įranga | ECU |
|---|
| 000040C4060C00 | 000040C5060C00 |
1.94.016 | 00005834060C01 |
BOSCH MD1CS001 (DME__DDE803P) |
| 000040C4060C00 | 000040C5060C00 |
1.94.007 | 00005834060C04 |
BOSCH MD1CS001 (DME__DDE803P) |
| 000040C4061100 | 000040C5061100 |
1.94.009 | 0000583406110A |
BOSCH MD1CS001 (DME__DDE803P) |
| 000040C4061600 | 000040C5061600 |
1.94.007 | 00005834061605 |
BOSCH MD1CS001 (DME__DDE803P) |
| 000040C4062000 | 000040C5062000 |
1.94.006 | 00005834062003 |
BOSCH MD1CS001 (DME__DDE803P) |
| 000040C4062100 | 000040C5062100 |
1.94.016 | 0000583406210C |
BOSCH MD1CS001 (DME__DDE803P) |
| 000040C4062100 | 000040C5062100 |
1.94.004 | 00005834062106 |
BOSCH MD1CS001 (DME__DDE803P) |
| 000040C40D1900 | 000040C50D1900 |
1.62.007 | 0000672A0D1904 |
BOSCH MD1CS001 (DME__DDE803P) |
| 000040C40D1B00 | 000040C50D1B00 |
1.62.004 | 0000672A0D1B09 |
BOSCH MD1CS001 (DME__DDE803P) |
| 000040C40D2100 | 000040C50D2100 |
1.94.004 | 0000672A0D210C |
BOSCH MD1CS001 (DME__DDE803P) |
ECU pastabos
Micro Infineon Tricore TC298TP This Setting File can be used for serial system NewGenius. To work on this ECU you can use NewTrasdata
Micro Infineon Tricore TC298TP To work on this ECU you can use NewTrasdata
Gaukite failą šiai transporto priemonei
Tools to read and write this ECU
