Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.
✓ Derinimas failu (flash)
✓ Galimas papildomas modulis 17 programinės įrangos versijos
Transporto priemonės duomenys
| Markė | AUDI |
| Modelis | Q3 (8U) |
| Variklis | 1.4L 16V TFSI 110kW/148HP MED17.5.25 |
| Serijinė galia | 150 CV / 11 kW |
| Darbinis tūris | 1400 cc |
| Kuras | Benzina sovralimentato |
| Transporto priemonės tipas | Auto |
ECU
| Gamintojas | BOSCH |
| Modelis | MED17.5.25 |
| Atmintis / EPROM | MICRO ST TRICORE - 20480 Kbit - 280000 |
Galimos derinimo operacijos / parinktys:
- Maximum air charge for overboost protection with turbocharger fault
- Base timing
- Optimal spark timing/MBT
- Advance correction
- Desired engine load calculation
- Lambda correction for engine temperature after starting
- Maximum torque limitation at clutch
- Compression ratio for turbocharger protection
- Compression ratio limiting for compressor depending on IAT sensor
- Maximum pressure ratio limit for diagnosis
- Exhaust gas temperature
- Engine indicated torque
- Factor for reducing maximum filling
- Gearbox maximum torque allowed
- High pressure fuel pump setpoint
- High fuel pressure pump limit for ECT sensor
- High fuel pressure pump limit
- High fuel pressure pump limit 2
- High pressure fuel pump setpoint - limp home mode
- High-pressure fuel pump - in catalyst heating monitoring mode
- Injection period - correction
- Intake valve lift
- Intake valve lift - catalyst heating
- Lambda enrichment for components protection
- Lambda correction for exhaust manifold temperature
- RPM Limiter
- RPM limiter 3
- RPM limiter - N
- RPM limiter in Park position
- RPM limit for ECT sensor
- RPM limit for EOT sensor
- Lambda driver wish
- Knock detection factor
- Speed limiter
- Speed limiter 2
- Maximum engine power
- Throttle air mass flow calculation
- Manifold absolute pressure time delay
- Characteristic manifold absolute pressure time constant of the LRS
- Maximum intake manifold pressure
- Max torque profile
- Optimal engine moment
- Power limit torque table
- Relative permissible torque from the pedal position in torque limitation
- Relative permissible torque from the pedal position in torque limitation - sport/race mode
- % relative air filling limit depending on IAT
- Driver torque request
- Driver torque request 2
- Driver torque request AWD
- Driver torque request for reverse gear
- Torque limiter for selected gear
- Setpoint maximum turbocharger speed
- Throttle angle management
- Maximum upper tolerance intake pressure protection
Programinės įrangos identifikatoriai (17)
| Aparatinės įrangos Nr. | Programinės įrangos Nr. (lustas) | Versija | Atnaujinimo programinė įranga | ECU |
|---|
| — | — |
1.94.013 | 04E906027GL 3136 |
BOSCH MED17.5.25 |
| — | — |
1.94.016 | 04E906027EK 2407 |
BOSCH MED17.5.25 |
| — | — |
1.94.006 | 04E906027NB 6699 |
BOSCH MED17.5.25 |
| — | 1037553962 |
1.94.018 | 04E906027CL 8980 |
BOSCH MED17.5.25 |
| — | — |
1.94.005 | 04E906027AQ 2893 |
BOSCH MED17.5.25 |
| — | 1037543755 |
1.94.016 | 04E906027CL 7783 |
BOSCH MED17.5.25 |
| — | — |
1.94.008 | 04E906027LA 3385 |
BOSCH MED17.5.25 |
| — | — |
1.94.015 | 04E906027KC 3597 |
BOSCH MED17.5.25 |
| — | — |
1.94.004 | 04E906027EM 2406 |
BOSCH MED17.5.25 |
| — | — |
1.94.009 | 04E906027CL 6239 |
BOSCH MED17.5.25 |
| — | — |
1.94.004 | 04E906027EM 2056 |
BOSCH MED17.5.25 |
| — | — |
1.94.007 | 04E906027EK 2897 |
BOSCH MED17.5.25 |
| — | — |
1.94.009 | 04E906027LA 3859 |
BOSCH MED17.5.25 |
| — | — |
1.94.009 | 04E906027NB 9504 |
BOSCH MED17.5.25 |
| — | — |
1.94.011 | 04E906027EK 0558 |
BOSCH MED17.5.25 |
| — | — |
1.94.006 | 04E906027KT 3858 |
BOSCH MED17.5.25 |
| — | — |
1.94.013 | 04E906027EL 2029 |
BOSCH MED17.5.25 |
Techninės pastabos apie automobilį
OBD located under the steering column, above the pedals. Visible or hidden by a plastic lid.
ECU pastabos
Microprocessor TC1782 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Gaukite failą šiai transporto priemonei
Tools to read and write this ECU
