Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.
✓ Derinimas failu (flash)
✓ Galimas papildomas modulis 2 programinės įrangos versijos
Transporto priemonės duomenys
| Markė | AUDI |
| Modelis | Q2 |
| Variklis | 2.0L 16V TDI 140kW/188HP EDC17C74 |
| Serijinė galia | 190 CV / 14 kW |
| Darbinis tūris | 2000 cc |
| Kuras | Diesel sovralimentato |
| Transporto priemonės tipas | Auto |
ECU
| Gamintojas | BOSCH |
| Modelis | EDC17C74 |
| Atmintis / EPROM | MICRO ST TRICORE - 32768 - 400000 |
Galimos derinimo operacijos / parinktys:
- Boost pressure limiter
- Boost pressure limiter 2
- Boost limiter correction for APS/BPS sensor
- Boost pressure limiter for ECT sensor
- Protection for cylinder head overheating
- Engine load - ceiling
- Maximum torque limitation at clutch
- Regeneration limit for DPF
- EGR valve control
- EGR valve control 2
- Max accepted exhaust gas temperature value before turbine
- Max accepted exhaust gas temperature value before turbine 2
- Protection for engine overheating
- Protection for engine overheating 2
- Basic torque management at engine cranking
- Injection period
- Injection period 2
- Injection period 3
- Injection period 4
- Injection period 5
- Injection period 6
- Injection period 7
- Injection period 8
- Injection period - correction
- Maximum injection period
- Injection opening time related to inj. pressure
- Initialization values over pressure control valve
- Injection 1
- Injection 2
- Boost pressure deviation limits for overboost detection
- Boost pressure deviation limit for underboost detection
- Boost pressure deviation limit for underboost detection 2
- Torque limiter
- Smoke limiter
- Lambda value of the smoke limitation
- Lambda value of the smoke limitation 2
- Speed limiter
- Speed limiter 2
- Maximum indicated torque for monitoring
- Protection for air load overheating
- Protection for exhaust gas temperature before turbine
- Protection for exhaust gas temperature before turbine 2
- Protection for fuel overheating
- Protection for fuel overheating 2
- Protection for oil overheating
- Pressure control map over pressure regulating valve
- Specific injection pressure limiter
- Specific injection pressure limiter 2
- Specific injection pressure limiter 3
- Specific injection pressure limiter for EFT sensor
- Specific injection pressure limiter for EFT sensor 2
- Relative permissible torque from the pedal position in torque limitation
- Maximum pressure ratio limit depending on temperature
- Specific injection pressure
- Specific injection pressure 2
- Specific injection pressure 3
- Specific injection pressure 4
- Q
- Air mass flow
- Driver torque request
- Driver torque request 2
- Driver torque request for reverse gear
- CAT downstream temperature sensor characterization
- CAT upstream temperature sensor characterization
- DPF downstream temperature sensor characterization
- Turbo upstream temperature sensor characterization
- Setpoint maximum turbocharger speed
- Overboost timing
- Overboost timing 2
- Overboost timing 3
- Overboost timing 4
- Turbocharger volumetric efficiency
Programinės įrangos identifikatoriai (2)
| Aparatinės įrangos Nr. | Programinės įrangos Nr. (lustas) | Versija | Atnaujinimo programinė įranga | ECU |
|---|
| — | — |
1.94.018 | 04L906026NQ 3614 |
BOSCH EDC17C74 |
| — | — |
1.94.019 | 04L906026NQ 4713 |
BOSCH EDC17C74 |
Techninės pastabos apie automobilį
OBD located to the left of the driver's side, accessible without removing anything to the left of the pedalboard.
ECU pastabos
MICRO Infineon Tricore TC1793 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Gaukite failą šiai transporto priemonei
Tools to read and write this ECU
