Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.
✓ Derinimas failu (flash)
✓ Galimas papildomas modulis 4 programinės įrangos versijos
Transporto priemonės duomenys
| Markė | AUDI |
| Modelis | A8 (D4/4H) |
| Variklis | 4.2L V8 32V TDI 283kW/380HP EDC17CP44 |
| Serijinė galia | 385 CV / 283 kW |
| Darbinis tūris | 4200 cc |
| Kuras | Diesel sovralimentato |
| Transporto priemonės tipas | Auto |
ECU
| Gamintojas | BOSCH |
| Modelis | EDC17CP44 |
| Atmintis / EPROM | MICRO ST TRICORE - 32768 Kbit - 400000 |
Galimos derinimo operacijos / parinktys:
- Boost pressure limiter
- Boost pressure
- Protection for cylinder head overheating
- Regeneration limit for DPF
- Regeneration limit for DPF 2
- EGR valve control
- EGR valve control 2
- EGR valve control 3
- Max accepted exhaust gas temperature value before turbine
- Protection for engine overheating
- Protection for engine overheating 2
- Protection for engine overheating 3
- Engine reference power at crankshaft
- Basic torque management at engine cranking
- Engine idle vs. ECT sensor
- Injection period
- Injection period 3
- Injection period 4
- Injection period 5
- Injection period 6
- Injection period 7
- Injection period 8
- Injection period 9
- Injection opening time related to inj. pressure
- Initialization values over pressure control valve
- Injection 1
- Injection 2
- Torque limiter
- Torque limiter for diagnostic
- Torque limiter for diagnostic 2
- Torque limiter for diagnostic 4
- Torque limiter during inactive pre-injection
- Smoke limiter
- RPM limit for ECT sensor
- RPM limit for ECT sensor 2
- Lambda reference
- Lambda value of the smoke limitation
- Minimum LSU sensor temperature limit - heater control
- Minimum LSU sensor temperature for O2
- Maximum LSU sensor temperature limit - heater control
- Maximum LSU sensor temperature for O2
- LSU temperature setpoint
- LSU temperature threshold PID heater governor activation
- Speed limiter
- Speed limiter - reverse gear
- Maximum indicated torque
- Maximum indicated torque for monitoring
- Maximum engine torque at crank shaft
- Protection for air load overheating
- Protection for exhaust gas temperature before turbine
- Protection for fuel overheating
- Protection for oil overheating
- Pressure control map over pressure regulating valve
- Specific injection pressure limiter
- Specific injection pressure limiter 2
- Specific injection pressure limiter 3
- Relative permissible torque from the pedal position in torque limitation
- Specific injection pressure
- Specific injection pressure 2
- Specific injection pressure 3
- Specific injection pressure - cold correction
- Driver torque request
- Driver torque request 2
- Driver torque request 3
- Driver torque request - AT
- Driver torque request for reverse gear
- CAT downstream temperature sensor characterization
- CAT upstream temperature sensor characterization
- DPF downstream temperature sensor characterization
- Turbo upstream temperature sensor characterization
- Torque limiter for the 1st gear selected
- Torque limiter for the 2nd gear selected
- Torque limiter for the 3rd gear selected
- Torque limiter for the 4th gear selected
- Torque limiter for the 5th gear selected
- Torque limiter for the 6th gear selected
- Torque limiter for the 7th gear selected
- Torque limiter for the 8th gear selected
- Torque limiter for the 9th gear selected
- Torque limiter for for reverse gear
- Torque limiter for the APS/BPS
- Variable geometry duty cycle limit
Programinės įrangos identifikatoriai (4)
| Aparatinės įrangos Nr. | Programinės įrangos Nr. (lustas) | Versija | Atnaujinimo programinė įranga | ECU |
|---|
| — | — |
1.00.028 | 4H0907409K 0003 |
BOSCH EDC17CP44 |
| — | — |
1.00.016 | 4H0907409AE 0008 |
BOSCH EDC17CP44 |
| — | — |
1.00.019 | 4H0907409AA 0001 |
BOSCH EDC17CP44 |
| — | — |
1.00.023 | 4H0907409AE 0005 |
BOSCH EDC17CP44 |
ECU pastabos
MICRO Infineon Tricore TC1797 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Gaukite failą šiai transporto priemonei
Tools to read and write this ECU
