Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.
✓ Derinimas failu (flash)
✓ Galimas papildomas modulis 5 programinės įrangos versijos
Transporto priemonės duomenys
| Markė | AUDI |
| Modelis | A4 (B9/8W) |
| Variklis | 50 3.0L 24V TDI 210kW/281HP MD1CP004 |
| Serijinė galia | 286 CV / 21 kW |
| Darbinis tūris | 3000 cc |
| Kuras | Diesel sovralimentato |
| Transporto priemonės tipas | Auto |
ECU
| Gamintojas | BOSCH |
| Modelis | MD1CP004 |
| Atmintis / EPROM | Micro Infineon TRICORE categoria AURIX. Il micro ha una DFLASH da 848 Kbyte |
Galimos derinimo operacijos / parinktys:
- Boost pressure limiter
- Maximum engine boost pressure F (atmospheric pressure)
- Boost pressure
- Boost pressure 2
- Boost pressure 3
- Boost pressure 4
- Boost pressure 5
- Boost pressure 6
- Boost pressure 7
- Boost pressure 8
- Protection for cylinder head overheating
- Maximum torque limitation at clutch
- Max accepted exhaust gas temperature value before turbine
- Max accepted exhaust gas temperature value before turbine 2
- Max accepted exhaust gas temperature value before turbine 3
- Protection for engine overheating
- Basic torque management at engine cranking
- Injection period
- Injection period 10
- Injection period 11
- Injection period 13
- Injection period 14
- Injection period 15
- Injection period 16
- Injection period 17
- Injection period 18
- Injection period 19
- Injection period 4
- Injection period 5
- Injection period 6
- Injection period 7
- Injection period 8
- Injection period 9
- Injection period limit
- Injection period limit 2
- Injection opening time related to inj. pressure
- Injection 1
- Injection 2
- Injection 3
- J
- Injection 5
- Torque limiter 2
- L
- Torque limiter 5
- Torque limiter
- LCL
- Lambda value of the smoke limitation
- Lambda value of the smoke limitation 2
- Lambda value of the smoke limitation 3
- Speed limiter
- Speed limiter 2
- Max torque profile - AT
- Protection for air load overheating
- Protection for exhaust gas temperature before turbine
- Protection for exhaust gas temperature before turbine 2
- Protection for fuel overheating
- Protection for oil overheating
- Pressure control map over pressure regulating valve
- Specific injection pressure limiter
- Specific injection pressure
- Specific injection pressure 2
- Specific injection pressure 3
- Specific injection pressure 4
- Specific injection pressure 5
- Driver torque request
- Driver torque request 2
- CAT downstream temperature sensor characterization
- CAT upstream temperature sensor characterization
- DPF downstream temperature sensor characterization
- Turbo upstream temperature sensor characterization
- Start of injection
- Start of injection 2
- Torque limiter for the APS/BPS
- Torque limiter in recovery mode
- Turbocharger volumetric efficiency
- Variable geometry duty cycle limit
Programinės įrangos identifikatoriai (5)
| Aparatinės įrangos Nr. | Programinės įrangos Nr. (lustas) | Versija | Atnaujinimo programinė įranga | ECU |
| — | — |
1.02.012 | 8W0907401G 0004 |
BOSCH MD1CP004 |
| — | — |
1.02.017 | 8W0907401B 0003 |
BOSCH MD1CP004 |
| — | — |
1.02.008 | 8W0907401K 0002 |
BOSCH MD1CP004 |
| — | — |
1.02.014 | 8W0907401L 0001 |
BOSCH MD1CP004 |
| — | — |
1.02.011 | 8W0907401H 0003 |
BOSCH MD1CP004 |
ECU pastabos
Microprocessor BGA FREESCALE SPC57xxx This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Micro Infineon Tricore TC298TP This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Gaukite failą šiai transporto priemonei
Tools to read and write this ECU