Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.
✓ Derinimas failu (flash)
15 programinės įrangos versijos
Transporto priemonės duomenys
| Markė | AUDI |
| Modelis | A4 (B8/8K) |
| Variklis | 2.0L 16V TDI 110kW/148HP EDC17C64 |
| Serijinė galia | 150 CV / 11 kW |
| Darbinis tūris | 2000 cc |
| Kuras | Diesel sovralimentato |
| Transporto priemonės tipas | Auto |
ECU
| Gamintojas | BOSCH |
| Modelis | EDC17C64 |
| Atmintis / EPROM | MICRO ST TRICORE - 32768 Kbit - 400000 |
Galimos derinimo operacijos / parinktys:
- Boost pressure limiter
- Boost pressure limiter 2
- Boost limiter correction for APS/BPS sensor
- Protection for cylinder head overheating
- Engine load - ceiling
- Max accepted exhaust gas temperature value before turbine
- Max accepted exhaust gas temperature value before turbine 2
- Max accepted exhaust gas temperature value at particulate sensor
- Protection for engine overheating
- Engine idle vs. ECT sensor
- Engine idle vs. ECT sensor 2
- Engine idle vs. ECT sensor 3
- Engine idle vs. ECT sensor 4
- Injection period
- Injection period 2
- Injection period 3
- Injection period 4
- Injection period 5
- Injection period 6
- Injection period - correction
- Maximum injection period
- Injection opening time related to inj. pressure
- Injection 1
- J
- Injection 3
- L
- Boost pressure deviation limits for overboost detection
- Boost pressure deviation limit for underboost detection
- Boost pressure deviation limit for underboost detection 2
- Torque limiter
- Smoke limiter
- Lambda value of the smoke limitation
- Lambda value of the smoke limitation 2
- Lambda value of the smoke limitation 4
- Lambda value of the smoke limitation 5
- Maximum indicated torque
- Protection for air load overheating
- Protection for exhaust gas temperature before turbine
- Protection for fuel overheating
- Protection for oil overheating
- Specific injection pressure limiter
- Specific injection pressure limiter 2
- Specific injection pressure limiter 3
- Specific injection pressure limiter for EFT sensor
- Specific injection pressure limiter for EOT sensor
- Relative permissible torque from the pedal position in torque limitation
- Maximum pressure ratio limit depending on temperature
- Specific injection pressure
- Specific injection pressure 2
- Specific injection pressure 3
- Specific injection pressure 4
- Q
- Specific air mass charge - correction
- Specific air mass charge - correction 2
- Driver torque request
- Driver torque request AWD
- Driver torque request for reverse gear
- Torque limiter for selected gear
- Setpoint maximum turbocharger speed
- Overboost timing
- Overboost timing 2
- Overboost timing 3
- Overboost timing 4
- Turbocharger volumetric efficiency
Programinės įrangos identifikatoriai (15)
| Aparatinės įrangos Nr. | Programinės įrangos Nr. (lustas) | Versija | Atnaujinimo programinė įranga | ECU |
|---|
| — | — |
1.94.018 | 04L906021CA 6822 |
BOSCH EDC17C64 |
| — | — |
1.94.011 | 04L997021D 3080 |
BOSCH EDC17C64 |
| — | — |
1.94.016 | 04L906021BT 8470 |
BOSCH EDC17C64 |
| — | — |
1.94.010 | 04L906021CB 9972 |
BOSCH EDC17C64 |
| — | — |
1.94.003 | 04L906021BT 9971 |
BOSCH EDC17C64 |
| — | — |
1.94.010 | 04L906021BS 8252 |
BOSCH EDC17C64 |
| — | — |
1.94.012 | 04L906021BS 6820 |
BOSCH EDC17C64 |
| — | — |
1.94.004 | 04L906021BS 8465 |
BOSCH EDC17C64 |
| — | — |
1.94.002 | 04L906021BT 9972 |
BOSCH EDC17C64 |
| — | — |
1.94.002 | 04L906021CA 8256 |
BOSCH EDC17C64 |
| — | — |
1.94.012 | 04L906021CA 9972 |
BOSCH EDC17C64 |
| — | — |
1.94.010 | 04L906021BS 9972 |
BOSCH EDC17C64 |
| — | — |
1.94.012 | 04L906021CA 8466 |
BOSCH EDC17C64 |
| — | — |
1.94.005 | 04L906021CB 9971 |
BOSCH EDC17C64 |
| — | — |
1.94.010 | 04L906021BQ 8285 |
BOSCH EDC17C64 |
Techninės pastabos apie automobilį
OBD located to the left of the driver's side, accessible without removing anything to the left of the pedalboard.
ECU pastabos
MICRO Infineon Tricore TC1797 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Gaukite failą šiai transporto priemonei
Tools to read and write this ECU
