Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.
✓ Derinimas failu (flash)
✓ Galimas papildomas modulis 4 programinės įrangos versijos
Transporto priemonės duomenys
| Markė | AUDI |
| Modelis | A4 (B7/8E/8H) |
| Variklis | 3.0L V6 24V TDI 150kW/201HP EDC16+ |
| Serijinė galia | 204 CV / 15 kW |
| Darbinis tūris | 3000 cc |
| Kuras | Diesel sovralimentato |
| Transporto priemonės tipas | Auto |
ECU
| Gamintojas | BOSCH |
| Modelis | EDC16U31/U34/CP34 |
| Atmintis / EPROM | M58BW016DB PQFP80 - Flash 3_V 512 x 32 |
Galimos derinimo operacijos / parinktys:
- Boost pressure limiter
- Maximum engine boost pressure F (atmospheric pressure)
- Boost pressure
- Boost pressure 2
- Maximum torque limitation at clutch
- Load / throttle position reference
- EGR valve control
- EGR valve control 2
- Exhaust gas temperature
- Protection for engine overheating
- Basic torque management at engine cranking
- Engine idle vs. ECT sensor
- Injection period
- Injection period 2
- Injection period - correction
- Injection opening time related to inj. pressure
- J
- Injection 2
- Torque limiter 2
- Lambda value of the smoke limitation
- Minimum LSU sensor temperature limit - heater control
- Minimum LSU sensor temperature for O2
- Maximum LSU sensor temperature limit - heater control
- Maximum LSU sensor temperature for O2
- LSU temperature threshold PID heater governor activation
- Protection for air load overheating
- Protection for fuel overheating
- Protection for oil overheating
- Specific injection pressure limiter
- Specific injection pressure
- Specific injection pressure 2
- Specific air mass charge 2
- Driver torque request
- Torque limiter for the 1st gear selected
- Torque limiter for the 2nd gear selected
- Torque limiter for the 3rd gear selected
- Torque limiter for the 4th gear selected
- Torque limiter for the 5th gear selected
- Torque limiter for the 6th gear selected
- Torque limiter for for reverse gear
- Torque limiter for the APS/BPS
- Torque limiter in recovery mode
- Turbocharger volumetric efficiency
- Variable geometry duty cycle limit
- Variable geometry duty cycle limit 2
Programinės įrangos identifikatoriai (4)
| Aparatinės įrangos Nr. | Programinės įrangos Nr. (lustas) | Versija | Atnaujinimo programinė įranga | ECU |
|---|
| — | — |
1.67.014 | 8E0997401Q 0001 |
BOSCH EDC16U31/U34/CP34 |
| — | 1037372780 |
1.67.023 | 8E0910401F 0020 |
BOSCH EDC16U31/U34/CP34 |
| — | 1037374489 |
1.67.035 | 8E0910401F 0040 |
BOSCH EDC16U31/U34/CP34 |
| — | 1037376009 |
1.67.031 | 8E0910401F 0050 |
BOSCH EDC16U31/U34/CP34 |
Techninės pastabos apie automobilį
OBD located to the left of the driver's side, accessible without removing anything to the left of the pedalboard.
ECU pastabos
Original EPROM ST M58BW016DB PQFP 80 Pin - Microprocessor Motorola MPC561/2/3/4. This Setting File can be used for serial system NewGenius. To modify this Ecu you can use the BDM system:555PRO or TRASDATA. WARNING:TRASDATA DO NOT need additional tools, 555PRO instead requires recalculation chks with VAG EDC16 CHECKSUM tool supplied with 555PRO, otherwise you will cause the block of the ecu or the detection of a change in the Ecu through diagnostic tool.
Gaukite failą šiai transporto priemonei
Tools to read and write this ECU
