ECU 数据库 ›
AUDI › AUDI A7 (4G8) 3.0L V6 24V TDI 150kW/201HP EDC17CP44
查找固件标识（硬件、软件和升级编号）、可用的调校选项，以及如何获取原始或改写文件。
✓ 通过文件调校 (flash)
✓ 附加模块可用 4 固件版本
车辆数据
| 品牌 | AUDI |
| 型号 | A7 (4G8) |
| 发动机 | 3.0L V6 24V TDI 150kW/201HP EDC17CP44 |
| 原厂功率 | 204 CV / 15 kW |
| 排量 | 3000 cc |
| 燃料 | Diesel sovralimentato |
| 车辆类型 | Auto |
ECU
| 制造商 | BOSCH |
| 型号 | EDC17CP44 |
| 存储 / EPROM | MICRO ST TRICORE - 32768 Kbit - 400000 |
可用的调校选项:
- Boost pressure limiter
- Boost pressure limiter 2
- Boost pressure
- Protection for cylinder head overheating
- Regeneration limit for DPF
- Regeneration limit for DPF 2
- EGR valve control
- EGR valve control 2
- EGR valve control 3
- EGR valve control 4
- Max accepted exhaust gas temperature value before turbine
- Max accepted exhaust gas temperature value before turbine 2
- Protection for engine overheating
- Protection for engine overheating 2
- Protection for engine overheating 3
- Engine reference power at crankshaft
- Basic torque management at engine cranking
- Engine idle vs. ECT sensor
- Injection period
- Injection period 2
- Injection period 3
- Injection period 4
- Injection period 5
- Injection opening time related to inj. pressure
- Initialization values over pressure control valve
- Injection 1
- J
- Torque limiter
- Torque limiter for diagnostic
- Torque limiter for diagnostic 4
- Torque limiter during inactive pre-injection
- Smoke limiter
- RPM limit for ECT sensor
- RPM limit for ECT sensor 2
- Lambda reference
- Lambda value of the smoke limitation
- Minimum LSU sensor temperature limit - heater control
- Minimum LSU sensor temperature for O2
- Maximum LSU sensor temperature limit - heater control
- Maximum LSU sensor temperature for O2
- LSU temperature setpoint
- LSU temperature threshold PID heater governor activation
- Speed limiter
- Speed limiter - reverse gear
- Maximum indicated torque
- Maximum indicated torque for monitoring
- Maximum engine torque at crank shaft
- Protection for air load overheating
- Protection for exhaust gas temperature before turbine
- Protection for exhaust gas temperature before turbine 2
- Protection for fuel overheating
- Protection for oil overheating
- Pressure control map over pressure regulating valve
- Specific injection pressure limiter
- Specific injection pressure limiter 2
- Specific injection pressure limiter 3
- Specific injection pressure limiter 4
- Relative permissible torque from the pedal position in torque limitation
- Specific injection pressure
- Specific injection pressure 2
- Specific injection pressure 3
- Specific injection pressure - cold correction
- Driver torque request
- Driver torque request 2
- Driver torque request 3
- Driver torque request - AT
- Driver torque request for reverse gear
- CAT downstream temperature sensor characterization
- CAT upstream temperature sensor characterization
- DPF downstream temperature sensor characterization
- Turbo upstream temperature sensor characterization
- Torque limiter for the 1st gear selected
- Torque limiter for the 2nd gear selected
- Torque limiter for the 3rd gear selected
- Torque limiter for the 4th gear selected
- Torque limiter for the 5th gear selected
- Torque limiter for the 6th gear selected
- Torque limiter for the 7th gear selected
- Torque limiter for the 8th gear selected
- Torque limiter for the 9th gear selected
- Torque limiter for for reverse gear
- Torque limiter for the APS/BPS
- Variable geometry duty cycle limit
- Variable geometry duty cycle limit 2
固件标识 (4)
| 硬件号 | 软件号 (chip) | 版本 | 升级软件 | ECU |
|---|
| — | — |
1.94.014 | 4G0907311G 0002 |
BOSCH EDC17CP44 |
| — | — |
1.00.029 | 4G0907311E 0002 |
BOSCH EDC17CP44 |
| — | — |
1.94.009 | 4G0907311G 0001 |
BOSCH EDC17CP44 |
| — | — |
1.00.015 | 8K5907311 0001 |
BOSCH EDC17CP44 |
车辆技术说明
OBD located to the left of the driver's side, accessible without removing anything to the left of the pedalboard.
ECU 说明
MICRO Infineon Tricore TC1797 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
