PORSCHE BOXSTER (987) 3.2L 24V S 206kW/276HP ME7.8.1 — ECU BOSCH ME7.8.1

Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.

✓ Derinimas failu (flash) ✓ Galimas papildomas modulis 10 programinės įrangos versijos

Gaukite failą šiai transporto priemonei

Pirkti failą (originalų arba perprogramuotą)Užsiregistruokite mastertuningfile.com ir užsisakykite failą

Esate servisas ar derintojas?

Transporto priemonės duomenys

Markė	PORSCHE
Modelis	BOXSTER (987)
Variklis	3.2L 24V S 206kW/276HP ME7.8.1
Serijinė galia	280 CV / 206 kW
Darbinis tūris	3200 cc
Kuras	Benzina aspirato
Transporto priemonės tipas	Auto

ECU

Gamintojas	BOSCH
Modelis	ME7.8.1
Atmintis / EPROM	29F800 PSOP44 8Mbit - Flash 512K x 16

Galimos derinimo operacijos / parinktys:

Base timing
Minimum advance allowed
Optimal spark timing/MBT
Desired engine load calculation
Lambda correction for engine temperature after starting
Exhaust gas temperature
Factor to correct fuel delivery system
Factor to correct fuel delivery system 2
HFM/HLM air flow high limit
HFM/HLM air flow low limit
Lambda enrichment for components protection
Torque limiter at high EGT
Lambda efficiency
RPM Limiter
RPM limiter in Park position
Lambda driver wish
Knock detection factor
MAF sensor calibration
Maximum indicated torque
Maximum ignition delay allowed for knock limiter intervention
Maximum possible engine charge
Throttle air mass flow calculation
Minimum engine air charge value
Number of injections considered for knock limitation
Optimal engine moment
Offset tolerance depending on permissible torque
Relative permissible torque from the pedal position in torque limitation
Relative permissible torque from the pedal position in torque limitation - sport/race mode
Relative permissible torque from the pedal position in torque limitation - sport/race mode 2
Driver wish
Driver torque request
Driver torque request for reverse gear
Driver torque request Sport mode
Maximum threshold for detecting engine knock - bank 1
Maximum threshold for detecting engine knock - bank 2
Throttle angle management
Variable intake pulsation correction

Programinės įrangos identifikatoriai (10)

Aparatinės įrangos Nr.	Programinės įrangos Nr. (lustas)	Versija	Atnaujinimo programinė įranga	ECU
0261208300	1037369620	1.27.013	00419100A8225C09	BOSCH ME7.8.1
0261208300	1037369620	1.27.004	00419100A8225C04	BOSCH ME7.8.1
0261208300	1037369620	1.27.009	00419100A7225C29	BOSCH ME7.8.1
0261208300	1037369620	1.27.006	00419100A7225C28	BOSCH ME7.8.1
0261208300	1037369620	1.27.012	00419100A8225C0D	BOSCH ME7.8.1
0261208300	1037369620	1.27.006	00419100A7225C0D	BOSCH ME7.8.1
0261208300	1037369620	1.27.004	00419100A8225C03	BOSCH ME7.8.1
0261208300	1037369620	1.27.008	00419100A7225C13	BOSCH ME7.8.1
0261208300	1037369620	1.27.010	00419100A8225C08	BOSCH ME7.8.1
0261208300	1037369620	1.27.018	00419100A7225C18	BOSCH ME7.8.1

ECU pastabos

Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION! This Setting File can be used for serial programming system NewGenius.

Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. This Setting File can be used for serial system NewGenius. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION!

Original EPROM PSOP 44 pins 29F800BB. This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION!

Galimi papildomi moduliai

A plug-and-play add-on module is available for this vehicle (as an alternative or in addition to the file):

Rapid FR - Modulo Aggiuntivo Dimsport € 189 Buy

Rapid FR Compact 2 - Modulo Aggiuntivo Dimsport € 215 Buy

→ See all add-on modules on the shop

Gaukite failą šiai transporto priemonei

Pirkti failą (originalų arba perprogramuotą)Užsiregistruokite mastertuningfile.com ir užsisakykite failą Esate servisas ar derintojas?Siūlykite šias paslaugas patys: aktyvuokite savo TuningFile platformą

Tools to read and write this ECU

Flex Programmatore per rimappatura centraline e cambi automatici ECU + auto gearbox € 1.000 Buy

The Genius OBD + Bench € 2.500 Buy

Kiti PORSCHE

911
3.2L CARRERA 170kW/228HP Motronic 924
2.5L 16V S 110kW/148HP 944
3.0L S2 155kW/208HP Motronic 944
2.5L Turbo 162kW/217HP Motronic 993
3.6L CARRERA 200kW/268HP M2.7 968
3.0L 177kW/237HP M2.7 928
5.0L S4 235kW/315HP 996
3.4L CARRERA 221kW/296HP M5.2.2 996
3.4L CARRERA 221kW/296HP ME7.2 964
3.6L TURBO S 280kW/376HP M2.7

→ Visos ECU PORSCHE