PORSCHE BOXSTER (986) 3.2L 24V S 191kW/256HP ME7.8 min

ECU BOSCH ME7.8 min · 260 CV (191 kW) · 3200 cc · Benzina aspirato

ECU duomenų bazėPORSCHE › PORSCHE BOXSTER (986) 3.2L 24V S 191kW/256HP ME7.8 min

Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.

✓ Derinimas failu (flash) 10 programinės įrangos versijos

Transporto priemonės duomenys

MarkėPORSCHE
ModelisBOXSTER (986)
Variklis3.2L 24V S 191kW/256HP ME7.8 min
Serijinė galia260 CV / 191 kW
Darbinis tūris3200 cc
KurasBenzina aspirato
Transporto priemonės tipasAuto

ECU

GamintojasBOSCH
ModelisME7.8 min
Atmintis / EPROM29F800 PSOP44 8Mbit - Flash 512K x 16

Galimos derinimo operacijos / parinktys:

  • Base timing
  • Minimum advance allowed
  • Optimal spark timing/MBT
  • Desired engine load calculation
  • Lambda correction for engine temperature after starting
  • Exhaust gas temperature
  • Factor to correct fuel delivery system
  • HFM/HLM air flow high limit
  • HFM/HLM air flow low limit
  • Lambda enrichment for components protection
  • Lambda efficiency
  • RPM Limiter
  • RPM limiter in Park position
  • Lambda driver wish
  • Knock detection factor
  • Speed limiter
  • MAF sensor calibration
  • Maximum ignition delay allowed for knock limiter intervention
  • Throttle air mass flow calculation
  • Minimum engine air charge value
  • Number of injections considered for knock limitation
  • Optimal engine moment
  • Offset tolerance depending on permissible torque
  • Relative permissible torque from the pedal position in torque limitation
  • Relative permissible torque from the pedal position in torque limitation 3
  • Driver wish
  • Driver torque request
  • Driver torque request for reverse gear
  • Maximum threshold for detecting engine knock - bank 1
  • Maximum threshold for detecting engine knock - bank 2
  • Throttle angle management
  • Variable intake pulsation correction

Programinės įrangos identifikatoriai (10)

Aparatinės įrangos Nr.Programinės įrangos Nr. (lustas)VersijaAtnaujinimo programinė įrangaECU
02612065791037350598 1.27.0040041610047203729 BOSCH ME7.8 min
02612065791037350598 1.27.0060041610047203719 BOSCH ME7.8 min
02612065791037350598 1.27.01800416100431D3708 BOSCH ME7.8 min
02612065791037350598 1.27.0060041610047203711 BOSCH ME7.8 min
02612065791037350598 1.27.00900416100421D3703 BOSCH ME7.8 min
02612065791037350598 1.27.0070041610047203728 BOSCH ME7.8 min
02612065791037350598 1.27.0200041610047203718 BOSCH ME7.8 min
02612065791037350598 1.27.0100041610047203718 BOSCH ME7.8 min
02612065791037350598 1.27.0030041610046303703 BOSCH ME7.8 min
02612065791037350598 1.27.0030041610046303704 BOSCH ME7.8 min

ECU pastabos

Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION! This Setting File can be used for serial programming system NewGenius.
Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. This Setting File can be used for serial programming system NewGenius. To work on this ECU you can use NewTrasdata ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION!