Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.
✓ Derinimas failu (flash)
✓ Galimas papildomas modulis 13 programinės įrangos versijos
Transporto priemonės duomenys
| Markė | PORSCHE |
| Modelis | 997 |
| Variklis | 3.8L GT3 RS Mk2 331kW/444HP ME7.8.2 min |
| Serijinė galia | 450 CV / 331 kW |
| Darbinis tūris | 3800 cc |
| Kuras | Benzina aspirato |
| Transporto priemonės tipas | Auto |
ECU
| Gamintojas | BOSCH |
| Modelis | ME7.8.2 min |
| Atmintis / EPROM | 29F800 PSOP44 8Mbit - Flash 512K x 16 |
Galimos derinimo operacijos / parinktys:
- Base timing
- Minimum advance allowed
- Optimal spark timing/MBT
- Desired engine load calculation
- Lambda correction for engine temperature after starting
- Exhaust gas temperature
- Factor to correct fuel delivery system
- Factor to correct fuel delivery system 2
- HFM/HLM air flow high limit
- HFM/HLM air flow low limit
- Lambda enrichment for components protection
- Lambda correction for exhaust manifold temperature
- Lambda efficiency
- RPM Limiter
- RPM Limiter 2
- Lambda driver wish
- Knock detection factor
- MAF sensor calibration
- Maximum ignition delay allowed for knock limiter intervention
- Throttle air mass flow calculation
- Minimum engine air charge value
- Number of injections considered for knock limitation
- Optimal engine moment
- Offset tolerance depending on permissible torque
- Relative permissible torque from the pedal position in torque limitation
- Relative permissible torque from the pedal position in torque limitation - sport/race mode
- Driver wish
- Driver torque request
- Maximum threshold for detecting engine knock - bank 1
- Maximum threshold for detecting engine knock - bank 2
- Throttle angle management
- Variable intake pulsation correction
Programinės įrangos identifikatoriai (13)
| Aparatinės įrangos Nr. | Programinės įrangos Nr. (lustas) | Versija | Atnaujinimo programinė įranga | ECU |
|---|
| 0261201349 | 00419100E500 |
1.87.012 | 00419100E500UM0A |
BOSCH ME7.8.2 min |
| 0261201349 | 00419100E510 |
1.87.014 | 00419100E510ER0K |
BOSCH ME7.8.2 min |
| 0261201349 | 00419100E520 |
1.87.014 | 00419100E520EM0L |
BOSCH ME7.8.2 min |
| 0261201349 | 00419100E520 |
1.87.011 | 00419100E520UM0L |
BOSCH ME7.8.2 min |
| 0261201349 | 00419100E471 |
1.87.026 | 00419100E471EM07 |
BOSCH ME7.8.2 min |
| 0261201349 | 00419100E520 |
1.87.003 | 00419100E520JM0L |
BOSCH ME7.8.2 min |
| 0261201349 | 00419100E510 |
1.87.006 | 00419100E510JM0D |
BOSCH ME7.8.2 min |
| 0261201349 | 00419100E510 |
1.87.006 | 00419100E510FR0K |
BOSCH ME7.8.2 min |
| 0261201349 | 00419100E520 |
1.87.008 | 00419100E520ER0L |
BOSCH ME7.8.2 min |
| 0261201349 | 00419100E520 |
1.87.006 | 00419100E520F419 |
BOSCH ME7.8.2 min |
| 0261201349 | 00419100E520 |
1.87.011 | 00419100E520FR0L |
BOSCH ME7.8.2 min |
| 0261201349 | 00419100E520 |
1.87.004 | 00419100E520UR0L |
BOSCH ME7.8.2 min |
| 0261201349 | 00419100E510 |
1.87.003 | 00419100E510UR0J |
BOSCH ME7.8.2 min |
ECU pastabos
Microprocessor ST10F275 Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. To work on this ECU you can use NewTrasdata This Setting File can be used for serial system NewGenius. ATTENTION !! ME7 ECU ! You can use the emulator ONLY to see the TRACE. MODIFY with the emulator ONLY with the engine OFF; DON'T modify with the engine ON. IX/LCP = INJECTION AT FULL LOAD, DECREASE VALUE TO INCREASE INJECTION!
Microprocessor ST10F275 Original EPROM PSOP 44 pins 29F800BB. In order to read this EPROM with the eprom programmer you need the adapter for PSOP and the card 15A with EMP20 or 202B with EMP21. To work on this ECU you can use NewTrasdata This Setting File can be used for serial system NewGenius.
Gaukite failą šiai transporto priemonei
Tools to read and write this ECU
