BMW X1 SERIES E84 X1 20d 2.0L L4 16V 135kW/181HP EDC17C41

ECU BOSCH EDC17C41 (DDE701/721) · 184 CV (135 kW) · 2000 cc · Diesel sovralimentato

ECU duomenų bazėBMW › BMW X1 SERIES E84 X1 20d 2.0L L4 16V 135kW/181HP EDC17C41

Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.

✓ Derinimas failu (flash) ✓ Galimas papildomas modulis 13 programinės įrangos versijos

Transporto priemonės duomenys

MarkėBMW
ModelisX1 SERIES E84
VariklisX1 20d 2.0L L4 16V 135kW/181HP EDC17C41
Serijinė galia184 CV / 135 kW
Darbinis tūris2000 cc
KurasDiesel sovralimentato
Transporto priemonės tipasAuto

ECU

GamintojasBOSCH
ModelisEDC17C41 (DDE701/721)
Atmintis / EPROMMICRO ST TRICORE - 32768 Kbit - 400000

Galimos derinimo operacijos / parinktys:

  • Boost pressure limiter
  • Boost pressure
  • EGR valve control
  • EGR valve control 2
  • EGR valve control 3
  • Max accepted exhaust gas temperature value at particulate sensor
  • Exhaust gas temperature threshold for component protection
  • Protection for engine overheating
  • Protection for engine overheating 2
  • Protection for engine overheating 3
  • Basic torque management at engine cranking
  • Gearbox maximum torque allowed
  • Gearbox maximum torque allowed 2
  • Gearbox maximum torque allowed 3
  • Injection period
  • Injection period 2
  • Maximum injection period
  • Injection opening time related to inj. pressure
  • J
  • L
  • Torque limiter 3
  • Torque limiter 4
  • Torque limiter 5
  • Torque limiter
  • Torque limiter for diagnostic
  • Torque limiter during particulate filter overloading - pressure
  • Torque limiter during particulate filter overloading - temperature
  • Lambda value of the smoke limitation
  • Lambda value of the smoke limitation 2
  • Minimum LSU sensor temperature limit - heater control
  • Minimum LSU sensor temperature for O2
  • Maximum LSU sensor temperature limit - heater control
  • Maximum LSU sensor temperature for O2
  • LSU temperature setpoint
  • LSU temperature threshold PID heater governor activation
  • Speed limiter
  • Maximum indicated torque
  • Maximum indicated torque for monitoring
  • Maximum engine torque at crank shaft
  • Pressure control map over pressure regulating valve
  • Specific injection pressure limiter
  • Specific injection pressure limiter 2
  • Specific injection pressure limiter 3
  • Relative permissible torque from the pedal position in torque limitation
  • Specific injection pressure
  • Specific injection pressure 2
  • Specific injection pressure 3
  • Driver torque request
  • CAT upstream temperature sensor characterization
  • DPF upstream temperature sensor characterization
  • SCR upstream temperature sensor characterization
  • Torque limiter for EFT sensor
  • Turbocharger volumetric efficiency
  • Variable geometry duty cycle limit

Programinės įrangos identifikatoriai (13)

Aparatinės įrangos Nr.Programinės įrangos Nr. (lustas)VersijaAtnaujinimo programinė įrangaECU
08580308 1.00.02108581270 BOSCH EDC17C41 (DDE701/721)
08519009 1.00.00808572970 BOSCH EDC17C41 (DDE701/721)
08580308 1.00.01008581272 BOSCH EDC17C41 (DDE701/721)
08574352 1.00.01608575811 BOSCH EDC17C41 (DDE701/721)
08574352 1.00.02108575812 BOSCH EDC17C41 (DDE701/721)
08580308 1.00.01008581268 BOSCH EDC17C41 (DDE701/721)
08519009 1.00.03008572972 BOSCH EDC17C41 (DDE701/721)
08519009 1.00.01008572971 BOSCH EDC17C41 (DDE701/721)
08574352 1.00.02508575810 BOSCH EDC17C41 (DDE701/721)
08580308 1.00.01508581275 BOSCH EDC17C41 (DDE701/721)
08519009 1.00.03308572973 BOSCH EDC17C41 (DDE701/721)
08580308 1.00.01508581269 BOSCH EDC17C41 (DDE701/721)
08519009 1.00.01708572971 BOSCH EDC17C41 (DDE701/721)

Techninės pastabos apie automobilį

OBD located to the left of the driver's side, in the bulkhead close to the bonnet release lever.

ECU pastabos

MICRO Infineon Tricore TC1797 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata