Raskite programinės įrangos identifikatorius (aparatinės, programinės įrangos ir atnaujinimo numerius), galimas derinimo parinktis ir kaip gauti originalų arba perprogramuotą failą.
✓ Derinimas failu (flash)
✓ Galimas papildomas modulis 5 programinės įrangos versijos
Transporto priemonės duomenys
| Markė | ALFA ROMEO |
| Modelis | GIULIETTA |
| Variklis | 1.8L 16V TBi QUADRIFOGLIO 173kW/232HP MED17.3.1 |
| Serijinė galia | 235 CV / 173 kW |
| Darbinis tūris | 1800 cc |
| Kuras | Benzina sovralimentato |
| Transporto priemonės tipas | Auto |
ECU
| Gamintojas | BOSCH |
| Modelis | MED17.3.1 |
| Atmintis / EPROM | MICRO ST TRICORE - 12032 Kbit - 178000 |
Galimos derinimo operacijos / parinktys:
- Maximum air charge for overboost protection with turbocharger fault
- Base timing
- Advance at idle speed
- Optimal spark timing/MBT
- Boost pressure
- Desired engine load calculation
- Lambda correction for engine temperature after starting
- Maximum torque limitation at clutch
- Exhaust gas temperature
- Exhaust valves lift - catalyst heating
- Characteristic line correction factor for pressure ratio for turbocharger overspeed protection
- Factor to correct fuel delivery system
- Factor for reducing maximum filling
- High pressure fuel pump setpoint
- High pressure fuel pump setpoint 2
- High fuel pressure pump limit
- Intake valve lift - catalyst heating
- Advance limiter for component protection 1
- Torque limiter
- Torque limiter for diagnostic
- Lambda enrichment for components protection
- Lambda correction for exhaust manifold temperature
- Torque limiter at high EGT
- RPM Limiter
- RPM limiter 3
- RPM limit for EOT sensor
- Lambda driver wish
- Knock detection factor
- Speed limiter
- MAF sensor calibration
- Maximum indicated torque
- Throttle air mass flow calculation
- Manifold absolute pressure time delay
- Characteristic manifold absolute pressure time constant of the LRS
- Max torque profile
- Optimal engine moment
- Offset tolerance depending on permissible torque
- Percent accelerator pedal angle to desired throttle angle
- Power limit torque table
- Relative permissible torque from the pedal position in torque limitation
- Pressure ratio depending on IAT
- Maximum pressure ratio limit depending on temperature
- % relative air filling limit depending on IAT
- Driver torque request
- Throttle angle management
- Torque limiter in recovery mode
- Turbocharger volumetric efficiency
- Variable valve timing - inlet
- Variable valve timing - outlet
Programinės įrangos identifikatoriai (5)
| Aparatinės įrangos Nr. | Programinės įrangos Nr. (lustas) | Versija | Atnaujinimo programinė įranga | ECU |
|---|
| 0261S05618 | 1037529951 |
1.91.017 | — |
BOSCH MED17.3.1 |
| 0261S05618 | 1037518971 |
1.91.016 | — |
BOSCH MED17.3.1 |
| 0261S05618 | 1037512340 |
1.91.023 | — |
BOSCH MED17.3.1 |
| 0261S05618 | 1037509747 |
1.91.026 | — |
BOSCH MED17.3.1 |
| 0261S06928 | 1037512863 |
1.91.042 | — |
BOSCH MED17.3.1 |
Techninės pastabos apie automobilį
ECU located on or behind the engine block. It may be necessary to remove the engine cover. Difficulty: easy.
OBD located to the left of the driver's side, under the steering column and behind the bulkhead or the lid in the fuse box area.
ECU pastabos
MICRO Infineon Tricore TC1766 This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
Gaukite failą šiai transporto priemonei
Tools to read and write this ECU
