ECU 数据库 ›
AUDI › AUDI RS7 (C8) 4.0L V8 32V BiTURBO 445kW/597HP MG1CS008
查找固件标识(硬件、软件和升级编号)、可用的调校选项,以及如何获取原始或改写文件。
✓ 通过文件调校 (flash)
✓ 附加模块可用 3 固件版本
车辆数据
| 品牌 | AUDI |
| 型号 | RS7 (C8) |
| 发动机 | 4.0L V8 32V BiTURBO 445kW/597HP MG1CS008 |
| 原厂功率 | 605 CV / 445 kW |
| 排量 | 4000 cc |
| 燃料 | Benzina sovralimentato |
| 车辆类型 | Auto |
ECU
| 制造商 | BOSCH |
| 型号 | MG1CS008 |
| 存储 / EPROM | Micro Infineon TRICORE categoria AURIX. Il micro ha una DFLASH da 848 Kbyte |
可用的调校选项:
- Absolute boost limit
- Maximum air charge for overboost protection with turbocharger fault
- Base timing
- Advance at idle speed
- Minimum advance allowed
- Optimal spark timing/MBT
- Optimal spark timing/MBT 2
- Boost pressure limiter
- Desired engine load calculation
- Lambda correction for engine temperature after starting
- Driver torque limit for clutch protection
- Compression ratio for turbocharger protection
- Compression ratio limiting for compressor depending on IAT sensor
- Compression ratio limiting for compressor depending on IAT sensor 2
- Max accepted exhaust gas temperature at exhaust manifold
- Exhaust gas temperature
- Exhaust gas temperature 2
- Exhaust valves lift
- Characteristic line correction factor for pressure ratio for turbocharger overspeed protection
- Characteristic line correction factor for pressure ratio for turbocharger overspeed protection 2
- Boost pressure preload correction factor
- Factor for reducing maximum filling
- Engine torque reducing factor depending on temperature
- Engine idle vs. ECT sensor
- Gearbox maximum torque allowed
- Boost pressure control hysteresis
- HFM/HLM air flow high limit
- High pressure fuel pump setpoint
- High fuel pressure pump limit for ECT sensor
- High fuel pressure pump limit
- Intake valve lift
- Torque limiter 2
- L
- Advance limiter for component protection 1
- Boost pressure deviation limits for basic charge air pressure
- Boost pressure deviation limits for basic charge air pressure 2
- Torque limiter
- Torque limiter for electrical engine
- Torque limiter for electrical engine Sport mode
- Lambda enrichment for components protection
- Component protection activation delay
- Lambda minimum value for components protection
- Lambda value for components protection activation
- Lambda correction for exhaust manifold temperature
- RPM Limiter
- RPM Limiter 2
- RPM limiter - N
- RPM limiter in Park position
- Engine speed limit temperature based
- RPM limit for ECT sensor
- RPM limit for EOT sensor
- Lambda driver wish
- Knock detection factor
- Speed limiter
- Maximum indicated torque
- Maximum indicated torque for monitoring
- Maximum engine torque at crank shaft
- Maximum engine load based on exhaust back pressure
- Maximum engine load in case of exhaust valve error
- Maximum engine load in case of turbocharger error
- Maximum engine temperature for torque limitation
- Throttle air mass flow calculation
- Manifold absolute pressure time delay
- Characteristic manifold absolute pressure time constant of the LRS
- Maximum intake manifold pressure
- Maximum throttle angle opening for a given RPM
- Max torque profile
- Max wastegate dutycycle
- Optimal engine moment
- Optimal engine moment 2
- Power limit torque table
- % relative air filling limit depending on IAT
- Driver torque request
- Driver torque request 2
- Driver torque request 3
- Compressor surge line definition
- Throttle angle management
- Target Lambda for knock protection
- Torque limiter in recovery mode
- Torque limiter in recovery mode 2
- Torque limiter in recovery mode 3
- Torque limiter in recovery mode 4
- Torque limiter in recovery mode 5
- Minimum engine rpm threshold for diagnosis
- Minimum engine rpm threshold for diagnosis 2
- Turbocharger volumetric efficiency
固件标识 (3)
| 硬件号 | 软件号 (chip) | 版本 | 升级软件 | ECU |
| — | — |
1.02.009 | 4K0907557C 0003 |
BOSCH MG1CS008 |
| — | — |
1.02.008 | 4K0907557C 0004 |
BOSCH MG1CS008 |
| — | — |
1.02.006 | 4K0907557G 0002 |
BOSCH MG1CS008 |
ECU 说明
Microprocessor BGA FREESCALE SPC57xxx This setting file can be used with the New Genius, the protocol supports identification and writing only. IF the matching original file is already present in databank it can be used for the modification and the writing operation. To work on this ECU you can use NewTrasdata
可用附加模块
A plug-and-play add-on module is available for this vehicle (as an alternative or in addition to the file):